Radio show prep: run sheet, timing, music, levels and the log

Radio show prep is everything you settle before the mic opens: a run sheet with clock times, short notes for each segment, every track cleared and loaded, levels checked on a meter, and a log written once you are off air. This guide gives you a run sheet to copy, the encoder settings worth checking, a pre-air checklist that ends with proof the stream is up, and what to write down afterwards. It fits a weekly music hour, a church service feed or a two-host talk show.

Steps
9
Reviewed
Runs on
Radio
Written by
Get Stream Hosting

By the Get Stream Hosting team

Every step was checked against the software's official documentation by independent reviewers before publishing. Last reviewed .

Pre-flight check

The five things prep settles

Good prep answers five questions up front, so nothing on air depends on memory.

  • What airs, and when. The run sheet: every segment, its clock time and its length.
  • What you say. Segment notes: the point, the facts, the names, the line that gets you out.
  • What plays. Music and spots that you are licensed to air, already in the library or the playlist.
  • How it sounds. Microphone, music and guest lines checked on a meter, encoder settings confirmed.
  • What happened. An after-show log that the next presenter, your sponsor or your licensing report can use.

A run sheet to copy

Write one row per segment, in clock time from the top of the show. A clock time tells you at a glance whether you are early or late; a list of durations does not. This example is a one-hour music-and-talk show.

ClockSegmentSourceLengthOut cue
00:00Station ID, show openLibrary, mic1:00Name the show and the host
00:01Music set 1Library, 3 tracks11:00Back-time to 12:00
00:12Topic oneMic5:00Hard out at 17:00
00:17Sponsor spot and linkLibrary, mic1:00Sponsor name exactly as written
00:18Guest interviewCall-in queue12:00Wrap signal at 28:00
00:30Music set 2Library, 4 tracks14:00Drop the last track if long
00:44Listener messagesVoice messages, mic6:00Soft out
00:50Music set 3, closeLibrary, mic9:30Hard out at 59:30, then handover

Keep the sheet in view, and give a co-host the same copy. Simulcasting with cameras? The same sheet runs a live video channel.

Timing: back-time to the hard posts

A hard post is a moment that cannot move: the end of your slot, a sponsor spot sold for a time, the handover to the next show. Everything else is a soft post and gives way.

  1. Mark every hard post on the run sheet in bold.
  2. For the last element before each hard post, subtract its length from the post. That is the latest moment it can start.
  3. Write a drop list: the items you cut first when running long, in order.
  4. Write a fill list: a spare track, a station ID, a listener message, for when you run short.
  5. Glance at the clock at every segment change and compare it with the sheet.

On the paid SSL radio streaming plans each DJ account is limited to its own hours, and AutoDJ steps aside when a live DJ connects and takes over again afterwards. Your slot end is a real hard post: plan your close so the last word lands before it.

Segment notes a co-host can read

Notes are prompts, not a script. Each segment gets a few lines that someone else could pick up and present.

  • The point of the segment, in one sentence.
  • Two or three facts, each with where it came from.
  • Names, with how to say them.
  • For a guest: their title as they want it read, the first question, and the question you skip if time is short.
  • The out line, written word for word.

Guests and callers need their own prep. On Premium and Platinum, a call-in link lets listeners call from their browser; they agree to be on air, wait in your studio queue and only go live when you pick them. On Platinum, guests can join by link without an account. Send each guest the link with the time to join.

Music cleared, then loaded

Clear first: a track that is loaded but not licensed is still a problem. Keep your licences on file in the control panel, where country limits can be set to match them; on all plans the airplay log is sealed daily and royalty reports come out in the formats ASCAP, BMI, SOCAN, PRS and other societies use.

US webcasters on the statutory licence also work to a sound recording performance complement, counted over any 3 hours on one channel: at most 3 tracks off a single album, with 2 the most back to back; at most 4 by one featured artist, or off one box set or compilation, with 3 the most back to back. Paid-plan rotation follows these US rules for you; a live set is your own choice, so check the track list.

Then load. On a paid plan, upload every track and spot to the library before the day, and build the show playlist in the order of the run sheet. On Premium and Platinum, smart and folder playlists and the weekday, weekend and seasonal schedules are all set in the control panel. Platinum adds cue, intro and outro points and even loudness on every track.

Levels: set them on a meter

Ears adjust within minutes, so set levels by meter. A useful reference is EBU R 128, the broadcast loudness recommendation: programme loudness normalised to -23.0 LUFS, a tolerance of ±1.0 LU where a live programme cannot hit the target exactly, and a true peak that does not exceed -1 dBTP. Measure with a meter that follows ITU-R BS.1770. What matters most is that your voice, the music and each guest sit at the same loudness.

Encoder setting (BUTT)What to check
Server entryAddress, port, password and mountpoint copied from your control panel
Audio tab: codec and bitrateNo higher than your plan carries: 32 kbps on Free, 128 on Premium, up to 320 on Platinum
Audio tab: channel modeStereo or mono, as you intend; one input channel used for both sides gives mono
Record tabFolder and file name set, and start recording when connected ticked
Signal detectionPresent and absent levels (default -50.0 dB) set in the Audio tab

BUTT's VU meter reads in dBFS. If you tick Stop if signal is absent, a long pause in a talk segment can disconnect you; set the time generously or leave it off for live talk.

Premium and Platinum also include a browser studio encoder, with voice and music processing, music ducked under your voice, and a warning if the air goes silent.

Checks before you go live

  1. Run sheet open; your clock agrees with a reliable time source.
  2. Open the show playlist and confirm every track on the sheet is there.
  3. Speak, play a bed and let a guest talk, watching the meter for each.
  4. In the encoder, select the right server entry and confirm codec, bitrate and recording.
  5. Connect inside your slot and confirm the encoder's status line shows it is connected.
  6. Off the studio network (mobile data works), play the HTTPS listen link.
  7. Check the player shows your show title, not the previous one.

How to confirm: a second device plays your voice, the player shows your show, and the live listener list includes that device. A short delay between your mic and the phone is normal buffering.

The after-show log

Write the log within the hour, while the details are fresh, and keep it factual.

  • Actual on-air and off-air times.
  • What was dropped, what was added, and any track played that was not on the sheet.
  • Faults, each with the clock time: a dropout, a bad line, a missed cue.
  • Sponsor spots aired, with times.
  • Guests and callers, and any follow-up promised on air.
  • One thing to change next week.

Set the log beside the station's own records. With Premium or Platinum, live shows are recorded into the library, audience figures are kept per show, and proof-of-airing reports can go to advertisers; the airplay log runs on all plans. A recorded show can return as a rerun, and BUTT's local recording is your copy if anything else fails.

When it goes wrong

  • Encoder will not connect. Recheck address, port, mountpoint and password against the panel. BUTT keeps trying until you press stop, so watch its status line.
  • Silence on air. Off-air alerts go by email on all plans; Premium and Platinum add dead-air warnings and a fallback playlist for when no source is live. Platinum adds a backup source.
  • Running long. Work down the drop list; never cut the hard out.
  • Voice and music at different loudness. Go back to the meter, not the faders by ear.
  • Stuck on show night. Live chat is open 24/7, with an AI assistant that reads your account and hands you to staff on request. Tickets go through the help centre.

Questions people ask

Do I need a full script, or are notes enough?

Notes are enough for most segments. Write word for word only what must be exact: the show open, sponsor copy, legal lines and the out line of each segment. Everything else reads better from prompts.

Can I prepare and run a show on the free radio plan?

Yes. Free carries a single live stream, and any Icecast or SHOUTcast encoder can feed it, so the run sheet, notes and levels work the same. AutoDJ, the music library and recorded shows need a paid plan; on Free, play music from your own computer and record in your encoder.

How do I hand over cleanly to the next presenter or to AutoDJ?

Treat the end of your slot as a hard post and finish before it. On paid plans AutoDJ takes over when the live DJ disconnects, and Platinum adds a gapless DJ handoff and a standby slot. Tell the next presenter your actual off-air time from the log.

Can I pre-record a show instead of going live?

Yes, on Premium and Platinum: schedule recorded and syndicated shows, import a cue sheet, and set reruns and expiry dates. Platinum adds voice tracking between songs. Prep the run sheet the same way; the timing just happens in the edit instead of live.

What loudness should my show be?

Consistency matters more than one number. EBU R 128 sets -23.0 LUFS with -1 dBTP as the true-peak limit for broadcast, and it is a sound reference for matching voice and music. Measure with a BS.1770 meter and keep every source at the same loudness.

Radio

Put your show on air

Start a station on the free plan, or choose a paid plan for AutoDJ, recorded shows, call-ins and per-show audience figures.