RadioBOSS broadcast settings: connect, encode, and confirm you are on air

To broadcast from RadioBOSS, open Settings, then Options, then Broadcast, add an encoder with the "+" button, enter your server type, address, port, mount or stream ID and source password, pick a format your plan carries, tick the encoder and switch on "Broadcasting enabled". When the report in the bottom-left corner reads "Connected to server!", open your listen link in a browser and listen. This run sheet covers each field, the track-title settings, and the three errors you are most likely to meet.

Steps
8
Reviewed
Runs on
Radio
Written by
Get Stream Hosting

By the Get Stream Hosting team

Every step was checked against the software's official documentation by independent reviewers before publishing. Last reviewed .

Pre-flight check

The signal chain, end to end

RadioBOSS is the studio end of the chain. It reads audio from the playlist, encodes it on the fly and pushes it to a streaming server; the server hands one copy to every listener. RadioBOSS runs on Windows and can feed Icecast, SHOUTcast and compatible servers, with as many encoders as you need, each with its own settings.

On our SSL radio streaming service the server end is ours. New stations run on Icecast; a single control-panel setting changes yours to SHOUTcast DNAS 2.6 if you prefer it. Listeners tune in over an HTTPS link, so the player works on secure websites. You keep the programme in RadioBOSS; we keep the server running.

RadioBOSS also has a built-in broadcast server. Its maker describes it as limited and meant for a local network or for relays between stations, and does not recommend it for public internet radio. Send to a streaming server instead.

Settings to copy

Take every value from the encoder details in your radio control panel; the radio control panel lists them together. Type them in exactly as shown, without guessing.

RadioBOSS fieldIcecast stationSHOUTcast DNAS 2 station
Server type (wizard)IcecastShoutcast v2
Server addressHost name only, no http://Host name only, no http://
PortThe source port from the panelThe source port from the panel
Mount / Stream IDMount name, requiredStream ID number
UsernameOnly if the panel gives oneOnly if the panel gives one
PasswordSource passwordSource password
Encoder typeMP3 is the RadioBOSS defaultMP3 is the RadioBOSS default
BitrateNo higher than the plan allowsNo higher than the plan allows
Sample rate / Channels44100 Hz, stereo by default44100 Hz, stereo by default

On Platinum, your encoder connects to the nearest of five cities. Copy the encoder details for that set-up from the Radio section of your control panel. Older encoder details keep working too.

Adding the encoder, step by step

  1. In the top menu choose Settings, then Options....
  2. Select Broadcast, Metadata and fill in the station name, description, URL and genre. Every encoder uses these unless it overrides them.
  3. Select Broadcast on the left and press +. The encoder window opens.
  4. Press Configuration Wizard, choose the server type (Icecast, or Shoutcast v2 for a SHOUTcast DNAS 2 station), then enter the address, port and password. Add a username only if your panel lists one. Press Finish.
  5. Back in the encoder window, check the mount or stream ID, then set Sample rate, Encoder type, Bitrate and Channels.
  6. Open the Metadata tab and set how track names reach the server (see below). Press OK.
  7. In the encoders list, tick the encoder you just made and switch on Broadcasting enabled at the top. Press OK.
  8. Check the Source drop-down above the encoders list. Audio mix sends the playlist; Input 1 to Input 3 send a sound-card input, such as a mixing desk.

Confirm it: the report in the bottom-left corner shows Connected to server! (output 1), with your encoder's number in place of 1.

Format and bitrate against your plan

The bitrate you set in RadioBOSS should not exceed what your plan carries. The RadioBOSS default of MP3 at 128 kbps, 44100 Hz stereo, suits Premium as it stands; Free needs a lower number, and Platinum allows a higher one.

PlanHighest bitrateWhat to set in RadioBOSS
Free32 kbpsBitrate 32; talk radio sits well here
Premium128 kbpsThe default MP3 128 kbps stereo
PlatinumUp to 320 kbpsUp to 320; extra lighter streams for phones

When the right format is unclear, the RadioBOSS manual's own advice is to leave the default and ask your host. Encoder questions go to our live chat, which runs around the clock, or to a ticket; a member of staff joins the chat on request. Both start from support.

Track titles and station info

Titles come from Settings, Options, Metadata, and each encoder can override them on its own Metadata and Station Info tabs. Three settings matter most.

  • Broadcasting title format builds the title from tag variables such as %artist - %title. It can hold several lines that rotate.
  • Update title is either On track start or Periodically, every set number of seconds. Use Periodically when the format has more than one line.
  • StreamURL tag embeds a URL in the stream metadata, typically the artwork of the playing track.

Good titles are not cosmetic here. Our player shows listeners what is playing, so it shows exactly what your tags say. Keep the artist and title tags clean in the RadioBOSS library.

Checks before you go live

  1. The report shows Connected to server! with the right output number, and no red error follows it.
  2. Open your HTTPS listen link in a browser on another device. You hear the programme, slightly behind what RadioBOSS is playing.
  3. The title in the player changes when the next track starts.
  4. Open your station's listener statistics in the control panel: your own test listener shows among who is tuned in right now.
  5. On paid plans, AutoDJ yields as soon as RadioBOSS connects, so listeners get your feed, not the library.

RadioBOSS reads its count from the server it broadcasts to; when listeners connect to a different server, the manual explains how to point the encoder's Statistics tab at it with Specify the server to get the statistics from. Your control panel's statistics show who is listening either way.

When it goes wrong

Report saysWhat it meansWhat to check
Error 2100The password was refusedCopy the source password again; watch for spaces
Error 2Server not reachedAddress and port; remove http:// from the address; firewall or antivirus on the PC
Error -1Someone is already connectedA second PC or another DJ still on the source
Connected, but silentWrong sourceThe Source drop-down: Audio mix or the right Input

Any other error names the failing output. Open Settings, Options, Broadcast, select that encoder, press Edit and correct it. A proxy under Advanced blocks every connection unless it supports HTTP CONNECT, so leave it empty unless you need it.

When RadioBOSS is the wrong tool

RadioBOSS is Windows software. If your DJs work from Macs or want nothing to install, they can broadcast from a browser tab on Premium and Platinum, or use another Icecast or SHOUTcast encoder of their choice. If you want pictures with the sound, live video streaming accepts an RTMP feed (OBS, vMix or Wirecast work) and serves it to browsers as HLS. If a PC playing all day is the real problem, a paid plan's AutoDJ runs from your uploaded music with no studio machine switched on.

Questions people ask

Which server type do I choose in RadioBOSS for my station?

Choose the type your station runs. Every station starts on Icecast, so pick Icecast and fill in the mount. If you switched to SHOUTcast DNAS 2.6 in the control panel, choose Shoutcast v2 and use the stream ID the panel gives.

Can RadioBOSS send more than one stream at once?

Yes. RadioBOSS allows any number of encoders, each with its own server and format, and you tick each one you want live. On Platinum the station itself carries 3 streams, with lighter ones that suit phones.

Why do listeners hear music but no song titles?

Check the Metadata settings. The title format must use variables the tags actually contain, such as %artist and %title, and Update title must be set to On track start or a period. Tracks with empty tags send an empty title.

Can I send 128 kbps on the free plan?

Set RadioBOSS to the bitrate your plan carries. Free carries 32 kbps, Premium 128 kbps and Platinum up to 320 kbps. The free plan is there for trying the station on air; move up when you need more quality.

Will my live show cut off the AutoDJ?

On Premium and Platinum, AutoDJ fills the air between live shows and yields as soon as your encoder connects. Free stations have no AutoDJ, so they carry only what an encoder such as RadioBOSS sends.

Radio

Put your stream on air

Open a station, copy its encoder details into RadioBOSS, and confirm the connected message.