Radio loudness in LUFS: targets, true peak and a level playlist

Radio loudness in LUFS (Loudness Units relative to Full Scale) is how loud your programme sounds to a listener on average, measured with the ITU-R BS.1770 method, and true peak is the highest level the reconstructed waveform reaches, including peaks that fall between samples. Pick one integrated target, keep every track and every voice near it, and hold true peak below a ceiling. Listeners then stop reaching for the volume between songs, ads and the presenter.

Steps
7
Reviewed
Runs on
Radio
Written by
Get Stream Hosting

By the Get Stream Hosting team

Every step was checked against the software's official documentation by independent reviewers before publishing. Last reviewed .

Pre-flight check

What the loudness meter is telling you

A loudness meter reads four numbers, and each answers a different question. All of them come from ITU-R BS.1770, which filters the audio with a K-weighting curve before averaging it, so bass-heavy and bright material are compared the way the ear compares them. EBU Tech 3341 sets the time windows. LUFS and LKFS are the same unit under two names; a difference between two readings is expressed in LU.

ReadingWindowUse it for
Momentary (M)Sliding 0.4 s, not gatedInstant feedback while you talk or ride a fader
Short-term (S)Sliding 3 s, not gatedLevelling voice; the EBU recommends it for self-op studios
Integrated (I)Whole programme, gatedThe single number you normalise each track to
Loudness Range (LRA)Spread of short-term valuesHow much a track swings between soft and loud passages

Integrated loudness ignores silence: blocks of 400 ms quieter than -70 LUFS are dropped, then anything more than 10 LU below the remaining average is dropped too. That is why a quiet intro does not drag a track's figure down. LRA is the distance between the 10th and 95th percentile of the short-term readings, so a single fade-out or one loud hit does not dominate it. The EBU advises against quoting LRA for anything shorter than a minute, such as a station ID.

True peak (dBTP) is measured on an oversampled copy of the signal, because the real waveform can rise between two samples. A file whose sample peaks sit at 0 dBFS can still clip once it is decoded, so you set your ceiling in dBTP, not in sample peak.

Which target to pick

Choose one integrated target for the whole station and stay on it. The EBU publishes the figures below; your choice depends on where people listen.

SituationIntegrated targetTrue-peak ceilingWhere it comes from
Producing programmes and exchanging them-23.0 LUFS (live shows may sit within ±1.0 LU)-1 dBTPEBU R 128
Radio or stream distribution, default-23.0 LUFSPer EBU Tech 3344EBU R 128 s3 and s2
Stream heard on phones and in noisy placesInterim range -20.0 to -16.0 LUFSLeave more room at low bitratesEBU R 128 s2, Tech 3401
FFmpeg loudnorm with no options set-24.0 LUFS-2.0 dBTPFFmpeg documentation

Most internet stations compete with music apps on phones, which is exactly the case the interim range was written for. A station playing classical music or drama has good reason to sit lower, near -23 LUFS, and keep its dynamics. Whatever you pick, write it on the studio wall and give it to every DJ.

Lossy encoding adds overshoot. EBU Tech 3344 notes that relatively low bitrates generally produce more of it, so a stream at a low bitrate needs a lower limiter setting than the same audio at a high one. Measure the decoded stream, not only your files.

Levelling the music library

Normalise the music before it reaches air, rather than squashing an uneven playlist with a heavy limiter at the output. EBU Tech 3401 recommends exactly that order: level each file, or store its loudness as playback metadata, and keep strong processing for distribution.

  1. Copy the originals to a separate folder first and confirm the copy opened and played before you change anything. Never write normalised files over the only copy.
  2. Measure each track with FFmpeg's ebur128 filter (command below). Add peak=true to the filter, as ebur128=peak=true, and the summary also reports the true peak.
  3. For each track, run FFmpeg's loudnorm filter twice. First pass: set your target I, TP and LRA and print_format=json, and read the measured values it prints. Second pass: give those back as measured_I, measured_LRA, measured_TP and measured_thresh with linear=true, so the track is turned up or down as a whole instead of compressed.
  4. Set an output sample rate with -ar. The documentation warns that in dynamic mode loudnorm upsamples to 192 kHz to find true peaks.
  5. Measure the new file again. Integrated should land on your target and true peak below your ceiling.
ffmpeg -nostats -i input.mp3 -filter_complex ebur128 -f null -

Linear mode has two conditions: the target LRA must not be lower than the track's own LRA, and the gain must not push true peak over the target TP. If either fails, loudnorm falls back to dynamic mode, which compresses. A very quiet, very wide classical recording is the usual case; set a higher LRA target for it, or accept a lower level for that piece.

Then upload the levelled files to your AutoDJ library in the control panel, and keep the untouched originals in your backup folder.

Keeping live voices on target

Speech is where most level jumps come from: a presenter who leans in, a guest on a quiet laptop, a caller on a phone. Set the meter to the target and read it as relative LU, with your target shown as 0 LU.

  • Watch short-term loudness and keep the voice within ±2 LU of 0. On momentary loudness the EBU suggests a ±3 LU band instead.
  • Set mic gain so the voice sits on target at a normal speaking distance, then leave it alone; ride the fader, not the preamp.
  • Put a true-peak limiter last in the chain at your ceiling, so a laugh or a dropped mic cannot clip the encoder.
  • One EBU member broadcaster plays music at 0 LU and sets presenters 1 to 3 LU below it. Try it if your voice sounds pushed over the music.

If you broadcast from your own encoder, set levels in your mixer or processing before the encoder; our support desk can check the encoder settings with you.

Checks before you call it done

  1. Play a mixed hour: music, a station ID, an ad, a voice link.
  2. Point FFmpeg's ebur128 at your listen link instead of input.mp3, and stop it after ten minutes or more with FFmpeg's -t option.
  3. Read the summary. Integrated should be within about 1 LU of your target, and true peak (with peak=true) below your ceiling.
  4. Listen to the joins on a phone speaker and on headphones. Nobody should need the volume control between items.

If integrated reads low but true peak is at the ceiling, the material is too dynamic for the target; lower the target or add gentle compression. If one item jumps out, measure that file on its own.

What your station plan does for you

Get Stream Hosting serves every station over HTTPS from Icecast or SHOUTcast, and the SSL radio streaming plans differ in what they handle for you. On the free plan you relay a single live feed at 32 kbps from the Icecast or SHOUTcast encoder you already use, so all levelling happens on your side; at that bitrate leave generous true-peak room.

  • Premium: AutoDJ at 128 kbps with crossfade and silence trimming, a browser studio encoder with voice and music processing and a warning when the air goes silent, automatic music ducking whenever you speak, and dead-air alerts. Level your library before uploading.
  • Platinum: even loudness on every track in AutoDJ, cue, intro and outro points, up to 320 kbps and 3 streams so phones can take a lighter bitrate. Since lighter streams are lower bitrates, check true peak on each one.
  • On any plan you can see your current audience live; on Platinum you also get tune-outs for each track, so you can see whether listeners leave on a loud ad or a quiet link.

The plan page does not state the loudness target the even-loudness feature uses, so measure your listen link once after switching it on and set your live voice level to match what you read. For the same discipline on video channels, see live video streaming.

When a target will not fix it

  • A track that was clipped in mastering stays distorted at any level; replace the file.
  • A remote DJ sending an already limited, very loud feed will still sound flat after it is turned down. Agree the target with them before the show.
  • Loudness normalisation cannot fix a poor speech-to-music balance inside one recording; that is a mixing job.
  • Players that apply their own volume levelling may move your stream again. Your job is a consistent stream; theirs is out of your hands.

Questions people ask

Is LUFS the same as LKFS?

Yes. Both name the same measurement from ITU-R BS.1770; the EBU uses LUFS to follow international naming, and the ITU text uses LKFS. A reading of -23 LKFS and -23 LUFS describe the same level.

Should an internet radio station sit at -23 or -16 LUFS?

The EBU still names -23.0 LUFS as the goal, but allows an interim distribution level between -20.0 and -16.0 LUFS when listeners are on phones or in noisy places. A station aimed at mobile listeners can choose inside that range; the EBU sees classical and drama services as natural candidates for staying at -23 LUFS, which keeps their dynamics. Pick one figure and hold it across every item.

Why does my stream clip when my files peak at -1 dBFS?

Sample peaks miss the peaks that form between samples, and lossy encoding adds more overshoot on top, especially at low bitrates. Measure true peak with an oversampling meter, such as FFmpeg's ebur128 with peak=true, and set your limiter in dBTP with room to spare for your bitrate.

Do I have to re-encode every song to level a playlist?

Not always. The EBU accepts either changing the file or storing its loudness as metadata that the playout applies as a fixed gain. If your automation cannot do that, a two-pass linear loudnorm run in FFmpeg changes only the gain when its linear-mode conditions are met (otherwise it falls back to dynamic mode).

How long should I measure a live stream?

Long enough to cover a representative mix of music, speech and ads; ten minutes is a sensible minimum and an hour tells you more. Integrated loudness is an average over everything measured, so a short sample of one song only describes that song.

Radio

Put your levelled station on air

Begin free using your own encoder, or choose a paid plan for AutoDJ, the browser studio and, on Platinum, even loudness on every track.